Sunbury-on-Thames · Surrey
Glass Splashbacks in Sunbury-on-Thames
A glass splashback in Sunbury-on-Thames starts with templating after the worktops are fitted, then a written quote that fixes the price for the glass, colour and finish shown.
- TW16
- TW17
- KT12
- Guide from £225
Sunbury-on-Thames: glass splashbacks
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
The wall behind a splashback must be flat, sound and dry so the adhesive bonds evenly. Old tiles are usually removed and the wall made good, because uneven surfaces show through the glass and can create stress points behind the panel.
Included as standard
- Bonding with adhesive compatible with the painted back
- Toughened glass made to template with factory cut-outs
- Silicone-finished edges, final clean and care advice
- Survey and templating after worktops and hob are fitted
About Sunbury-on-Thames for this job
- Postcodes covered
- TW16, TW17, KT12 and the surrounding area, including Walton-on-Thames, Hampton and Hanworth
- Coast
- Sunbury-on-Thames is well inland, around 55 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Sunbury-on-Thames the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Sunbury-on-Thames
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Glass Splashbacks in Sunbury-on-Thames: questions
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
How do you match the colour of a glass splashback?
We can match many paint and RAL colours, and the most reliable way to choose is from a physical glass sample viewed in your own kitchen. Colours look different on screens and under different lighting. For pale colours we usually suggest low-iron glass, because standard glass adds a green tint to the painted back.
How do I clean a glass splashback?
Wipe it with a soft cloth and warm soapy water, or a non-abrasive glass cleaner, then buff dry for a streak-free finish. Grease behind the hob comes off easily because there are no grout lines. Avoid scourers, abrasive creams and blades, which can scratch the glass, and do not use cleaners that could seep behind the edges.
Do you cover Sunbury-on-Thames for glass splashbacks?
Yes. We can quote for glass splashbacks across Sunbury-on-Thames and the surrounding Surrey area, including postcode districts TW16, TW17 and KT12, and nearby Walton-on-Thames, Hampton and Hanworth. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Sunbury-on-Thames
Get a written quote in Sunbury-on-Thames
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.