Walton-on-Thames · Surrey
Glass Splashbacks in Walton-on-Thames
A glass splashback in Walton-on-Thames starts with templating after the worktops are fitted, then a written quote that fixes the price for the glass, colour and finish shown.
- KT12
- TW17
- TW16
- Guide from £225
About kitchen glass splashback in Walton-on-Thames
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
Colours look different on screens, in daylight and under kitchen lighting, so choose from a physical glass sample rather than a website or paint chart. We can match many paint and RAL colours, and a sample panel viewed in your own kitchen avoids surprises.
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
What you get
- Removal and refitting of socket and switch faceplates
- Bonding with adhesive compatible with the painted back
- Back-painting to your chosen colour or finish
- Survey and templating after worktops and hob are fitted
About Walton-on-Thames for this job
- Postcodes covered
- KT12, TW17, TW16 and the surrounding area, including Sunbury-on-Thames, Esher and Hampton
- Coast
- Walton-on-Thames is well inland, around 55 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Walton-on-Thames the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Walton-on-Thames
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
What you can choose
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Metallic or sparkle finish
Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.
Glass Splashbacks in Walton-on-Thames: questions
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
How do you match the colour of a glass splashback?
We can match many paint and RAL colours, and the most reliable way to choose is from a physical glass sample viewed in your own kitchen. Colours look different on screens and under different lighting. For pale colours we usually suggest low-iron glass, because standard glass adds a green tint to the painted back.
Do you cover Walton-on-Thames for glass splashbacks?
Yes. We can quote for glass splashbacks across Walton-on-Thames and the surrounding Surrey area, including postcode districts KT12, TW17 and TW16, and nearby Sunbury-on-Thames, Esher and Hampton. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Walton-on-Thames
Get a written quote in Walton-on-Thames
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.