Windsor · Berkshire
Safety Glass in Windsor
Safety glass for doors, side panels and low windows in Windsor can be made to the right class, with a permanent mark showing the standard.
- SL4
- Guide from £55
Toughened glass cut to size in Windsor
In England, Approved Document K requires safety glass in critical locations: glass in a door or within 300mm of a door edge, up to 1500mm above the floor, and other glass within 800mm of the floor. The rules are similar elsewhere in the UK, but the detail differs.
BS EN 12600 classifies safety glass by a pendulum impact test, with class 1 the highest and class 3 the lowest. In England, critical locations generally need at least class 3, and door or side panels wider than 900mm need class 2 or better.
When measuring for a replacement panel, measure the opening or old glass in at least two places for width and height, and note the thickness. For anything with holes, curves or angled corners, a hardboard or card template gives the most reliable result.
Laminated glass is two or more sheets bonded with a plastic interlayer, often PVB. If it breaks, the pieces stick to the interlayer and the pane stays in place. That makes it useful for overhead glass, ground-floor security and openings where an empty hole would be a risk.
What's included
- Measurement or templating of the glass panel
- Advice on toughened or laminated glass for the location
- Permanent safety marking on building glass
- Glass cut, edge-worked and drilled before toughening
Windsor at a glance
- Postcodes covered
- SL4 and the surrounding area, including Slough, Egham and Staines
- Coast
- Windsor is well inland, around 67 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Windsor the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- Older rural homes often have internal doors and screens with old, unmarked glass. Upgrading them to toughened or laminated safety glass is common, and timber door frames may need careful beading when the new glass is fitted.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Windsor
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Specification choices
Polished edges
Smooth, clear edges for exposed glass on tables, shelves and frameless panels, safer to handle and neater to look at.
Laminated safety glass
Two or more sheets bonded with an interlayer that holds broken glass in place, for overhead, security and fall-risk locations.
Toughened laminated glass
Toughened sheets laminated together, combining strength with post-breakage retention, often used for frameless panels and higher-load applications.
Safety Glass in Windsor: questions
What thickness of toughened glass do I need for a table or shelf?
It depends on the size, how the glass is supported and the load it will carry. Small side tables can use thinner glass, while large dining tables and long shelves need thicker panels to limit bending. Tell us the dimensions, support method and what it will hold, and we will confirm a suitable thickness in the quote.
How do I know if my glass is safety glass?
Look for a permanent mark etched or printed in a corner of the pane. It should name the maker or supplier and the standard, such as BS EN 12150 for toughened glass, or show a BS EN 12600 class. Older glass may have no mark. If you are unsure, a glazier can check and advise.
Should I choose a polished or arrised edge?
Choose polished edges where the edge will be seen or touched, such as tabletops, shelves and frameless panels, because they are smooth and look neat. Arrised edges are lightly sanded to remove sharpness and are fine where the edge sits hidden in a frame. Bevelled edges are decorative and suit mirrors and some tabletops.
How much does toughened glass cut to size cost?
The price depends on the dimensions, thickness, glass type, edge finish, number of holes and cut-outs, any shapes, and whether you want supply only or fitting. Laminated, low-iron and obscure glass cost more than clear toughened. See the guide prices for typical panels, then get a written quote for your exact specification.
Do you cover Windsor for safety glass?
Yes. We can quote for safety glass across Windsor and the surrounding Berkshire area, including postcode districts SL4, and nearby Slough, Egham and Staines. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Windsor
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.