Staines · Surrey
Safety Glass in Staines
Need a glass panel made to measure in Staines? Our glaziers confirm the thickness, edge finish and holes before the glass is toughened.
- TW15
- TW16
- TW17
- TW18
- Guide from £55
Safety glass for doors for homes and businesses in Staines
Laminated glass is two or more sheets bonded with a plastic interlayer, often PVB. If it breaks, the pieces stick to the interlayer and the pane stays in place. That makes it useful for overhead glass, ground-floor security and openings where an empty hole would be a risk.
Toughened glass is ordinary float glass that has been cut to size, heated and then cooled quickly with jets of air. This leaves the surfaces in compression, making it several times stronger than untreated glass of the same thickness. When it does break, it crumbles into small, relatively blunt pieces.
Toughened glass can, in rare cases, break without any obvious impact because of tiny nickel sulphide inclusions in the glass. Heat soak testing exposes the toughened glass to heat for a set period to break susceptible panes before supply, which reduces the risk without removing it completely.
Edge finish affects both look and safety. Arrised edges are lightly sanded to take off sharpness and suit glass held in frames. Polished edges are smooth and clear for exposed edges on tables, shelves and frameless panels. Bevelled edges add a decorative angled border.
What a typical job includes
- Measurement or templating of the glass panel
- Delivery or fitting by our glaziers
- Permanent safety marking on building glass
- Glass cut, edge-worked and drilled before toughening
Local details for Staines
- Postcodes covered
- TW15, TW16, TW17, TW18 and the surrounding area, including Egham, Ashford (Surrey) and Feltham
- Coast
- Staines is well inland, around 60 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Staines the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- Older rural homes often have internal doors and screens with old, unmarked glass. Upgrading them to toughened or laminated safety glass is common, and timber door frames may need careful beading when the new glass is fitted.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Staines
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Choosing your safety glass
Clear toughened glass
Heat-treated float glass that breaks into small, blunt pieces, for doors, screens, tabletops and shelves in a range of thicknesses.
Satin or obscure finish
Acid-etched or patterned glass for privacy in doors and screens, toughened or laminated to meet safety requirements.
Low-iron glass
Extra-clear glass with much less green tint, chosen for tabletops, shelving and panels where colour and edge clarity matter.
Safety Glass in Staines: questions
How do I know if my glass is safety glass?
Look for a permanent mark etched or printed in a corner of the pane. It should name the maker or supplier and the standard, such as BS EN 12150 for toughened glass, or show a BS EN 12600 class. Older glass may have no mark. If you are unsure, a glazier can check and advise.
Can toughened glass be cut or drilled after it is made?
No. Toughened glass cannot be cut, drilled or edge-worked once it has been toughened, because any damage to the surface releases the internal stress and the whole pane shatters. All sizes, holes and cut-outs must be finalised before toughening. That is why accurate measurements or a template are needed before the order is placed.
Can toughened glass break on its own?
Rarely, yes. Tiny nickel sulphide inclusions in the glass can expand over time and cause a toughened pane to break without an obvious impact. Edge damage during fitting can also cause later failure. Heat soak testing reduces the risk of inclusion-related breakage, and careful handling and correct fitting protect the edges.
Is laminated glass better for security?
Laminated glass usually gives better security than toughened glass of similar thickness, because the interlayer holds the glass together after it cracks, so making a hole takes more effort. Thicker interlayers and multi-layer laminates give more resistance. For ground-floor windows, shopfronts and doors, laminated glass is often chosen for this reason.
Do you cover Staines for safety glass?
Yes. We can quote for safety glass across Staines and the surrounding Surrey area, including postcode districts TW15, TW16, TW17 and TW18, and nearby Egham, Ashford (Surrey) and Feltham. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Staines
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.