Crewe · Cheshire
Safety Glass in Crewe
Need a glass panel made to measure in Crewe? Our glaziers confirm the thickness, edge finish and holes before the glass is toughened.
- CW1
- CW2
- Guide from £55
Toughened glass table top for homes and businesses in Crewe
Laminated glass is two or more sheets bonded with a plastic interlayer, often PVB. If it breaks, the pieces stick to the interlayer and the pane stays in place. That makes it useful for overhead glass, ground-floor security and openings where an empty hole would be a risk.
Edge finish affects both look and safety. Arrised edges are lightly sanded to take off sharpness and suit glass held in frames. Polished edges are smooth and clear for exposed edges on tables, shelves and frameless panels. Bevelled edges add a decorative angled border.
Glass tabletops and shelves need the right thickness for the span and load. Thicker glass deflects less, so a long shelf or a large table needs a heavier panel than a small side table. The supplier confirms a suitable thickness for the use, not just the size.
Toughened glass is ordinary float glass that has been cut to size, heated and then cooled quickly with jets of air. This leaves the surfaces in compression, making it several times stronger than untreated glass of the same thickness. When it does break, it crumbles into small, relatively blunt pieces.
What's included
- Measurement or templating of the glass panel
- Permanent safety marking on building glass
- Delivery or fitting by our glaziers
- Glass cut, edge-worked and drilled before toughening
About Crewe for this job
- Postcodes covered
- CW1, CW2 and the surrounding area, including Winsford, Kidsgrove and Congleton
- Coast
- Crewe is well inland, around 33 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Crewe the midwinter sun reaches about 14° above the horizon at noon, with roughly 7.3 hours of daylight, rising to about 60° and 16.7 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- In flats and city buildings, large panels of safety glass may need to fit through narrow stairs, lifts and doorways. Measuring access routes at the survey avoids problems, and laminated glass suits ground-floor doors and screens facing the street.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Crewe
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
What you can choose
Holes and cut-outs
Drilled holes for handles, hinges and fixings, and cut-outs for sockets, all made before the glass is toughened.
Laminated safety glass
Two or more sheets bonded with an interlayer that holds broken glass in place, for overhead, security and fall-risk locations.
Clear toughened glass
Heat-treated float glass that breaks into small, blunt pieces, for doors, screens, tabletops and shelves in a range of thicknesses.
Safety Glass in Crewe: questions
How much does toughened glass cut to size cost?
The price depends on the dimensions, thickness, glass type, edge finish, number of holes and cut-outs, any shapes, and whether you want supply only or fitting. Laminated, low-iron and obscure glass cost more than clear toughened. See the guide prices for typical panels, then get a written quote for your exact specification.
What thickness of toughened glass do I need for a table or shelf?
It depends on the size, how the glass is supported and the load it will carry. Small side tables can use thinner glass, while large dining tables and long shelves need thicker panels to limit bending. Tell us the dimensions, support method and what it will hold, and we will confirm a suitable thickness in the quote.
Where is safety glass required in a house?
In England, safety glass is needed in critical locations: glass in doors and within 300mm of a door edge, up to 1500mm above floor level, and other glass within 800mm of the floor. Small panes and leaded lights have specific exceptions. The rules elsewhere in the UK are similar, but the detail differs between nations.
Can toughened glass be cut or drilled after it is made?
No. Toughened glass cannot be cut, drilled or edge-worked once it has been toughened, because any damage to the surface releases the internal stress and the whole pane shatters. All sizes, holes and cut-outs must be finalised before toughening. That is why accurate measurements or a template are needed before the order is placed.
Do you cover Crewe for safety glass?
Yes. We can quote for safety glass across Crewe and the surrounding Cheshire area, including postcode districts CW1 and CW2, and nearby Winsford, Kidsgrove and Congleton. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Crewe
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.