Welling · Greater London
Safety Glass in Welling
Need a glass panel made to measure in Welling? Our glaziers confirm the thickness, edge finish and holes before the glass is toughened.
- DA16
- DA6
- DA15
- Guide from £55
Toughened glass panels in Welling: what to know
When measuring for a replacement panel, measure the opening or old glass in at least two places for width and height, and note the thickness. For anything with holes, curves or angled corners, a hardboard or card template gives the most reliable result.
Safety glass in a building should carry a permanent mark, usually in a corner, that stays visible after fitting. It names the maker or supplier and the standard, such as BS EN 12150 for toughened glass. The mark is how a buyer or inspector can confirm what was fitted.
Low-iron glass removes most of the slight green tint that ordinary clear glass shows at its edge and through thick panels. It suits tabletops, display shelves and splashback-style panels where true colours and a clearer edge matter.
In England, Approved Document K requires safety glass in critical locations: glass in a door or within 300mm of a door edge, up to 1500mm above the floor, and other glass within 800mm of the floor. The rules are similar elsewhere in the UK, but the detail differs.
What's included
- Permanent safety marking on building glass
- Written quote fixing the price for the specification
- Advice on toughened or laminated glass for the location
- Glass cut, edge-worked and drilled before toughening
Working in Welling
- Postcodes covered
- DA16, DA6, DA15 and the surrounding area, including Bexleyheath, Eltham and Thamesmead
- Coast
- Welling sits roughly 18 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Near the coast, salt spray can mark exposed glass edges and corrode metal fixings. Polished edges and sealed laminated edges cope better outdoors, and stainless steel clamps and hinges are worth specifying for external safety glass panels and screens.
- Daylight and sun
- In Welling the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- Older rural homes often have internal doors and screens with old, unmarked glass. Upgrading them to toughened or laminated safety glass is common, and timber door frames may need careful beading when the new glass is fitted.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Welling
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Options to choose between
Satin or obscure finish
Acid-etched or patterned glass for privacy in doors and screens, toughened or laminated to meet safety requirements.
Clear toughened glass
Heat-treated float glass that breaks into small, blunt pieces, for doors, screens, tabletops and shelves in a range of thicknesses.
Laminated safety glass
Two or more sheets bonded with an interlayer that holds broken glass in place, for overhead, security and fall-risk locations.
Safety Glass in Welling: questions
Where is safety glass required in a house?
In England, safety glass is needed in critical locations: glass in doors and within 300mm of a door edge, up to 1500mm above floor level, and other glass within 800mm of the floor. Small panes and leaded lights have specific exceptions. The rules elsewhere in the UK are similar, but the detail differs between nations.
How much does toughened glass cut to size cost?
The price depends on the dimensions, thickness, glass type, edge finish, number of holes and cut-outs, any shapes, and whether you want supply only or fitting. Laminated, low-iron and obscure glass cost more than clear toughened. See the guide prices for typical panels, then get a written quote for your exact specification.
Why do I need to wait for toughened glass?
Toughened glass is made to order. Each panel is cut, edge-worked and drilled from float glass, then heated and cooled in a toughening furnace. It cannot be cut from stock once toughened. Your written quote shows the expected timescale, and the glazier will confirm fitting arrangements once the glass is ready.
What thickness of toughened glass do I need for a table or shelf?
It depends on the size, how the glass is supported and the load it will carry. Small side tables can use thinner glass, while large dining tables and long shelves need thicker panels to limit bending. Tell us the dimensions, support method and what it will hold, and we will confirm a suitable thickness in the quote.
Do you cover Welling for safety glass?
Yes. We can quote for safety glass across Welling and the surrounding Greater London area, including postcode districts DA16, DA6 and DA15, and nearby Bexleyheath, Eltham and Thamesmead. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Welling
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.