Andover · Hampshire
Safety Glass in Andover
We cover Andover and Hampshire for toughened and laminated glass, supplied ready to fit or measured and installed by our glaziers.
- SP10
- Guide from £55
Toughened glass cut to size across Andover
Low-iron glass removes most of the slight green tint that ordinary clear glass shows at its edge and through thick panels. It suits tabletops, display shelves and splashback-style panels where true colours and a clearer edge matter.
BS EN 12600 classifies safety glass by a pendulum impact test, with class 1 the highest and class 3 the lowest. In England, critical locations generally need at least class 3, and door or side panels wider than 900mm need class 2 or better.
In England, Approved Document K requires safety glass in critical locations: glass in a door or within 300mm of a door edge, up to 1500mm above the floor, and other glass within 800mm of the floor. The rules are similar elsewhere in the UK, but the detail differs.
Toughened glass can, in rare cases, break without any obvious impact because of tiny nickel sulphide inclusions in the glass. Heat soak testing exposes the toughened glass to heat for a set period to break susceptible panes before supply, which reduces the risk without removing it completely.
What's included
- Advice on toughened or laminated glass for the location
- Measurement or templating of the glass panel
- Delivery or fitting by our glaziers
- Written quote fixing the price for the specification
Working in Andover
- Postcodes covered
- SP10 and the surrounding area, including Winchester, Newbury and Salisbury
- Coast
- Andover is well inland, around 35 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Andover the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- Older rural homes often have internal doors and screens with old, unmarked glass. Upgrading them to toughened or laminated safety glass is common, and timber door frames may need careful beading when the new glass is fitted.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Andover
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Specification choices
Laminated safety glass
Two or more sheets bonded with an interlayer that holds broken glass in place, for overhead, security and fall-risk locations.
Holes and cut-outs
Drilled holes for handles, hinges and fixings, and cut-outs for sockets, all made before the glass is toughened.
Clear toughened glass
Heat-treated float glass that breaks into small, blunt pieces, for doors, screens, tabletops and shelves in a range of thicknesses.
Safety Glass in Andover: questions
What is the difference between toughened and laminated glass?
Toughened glass is heat treated so it is stronger and, if broken, crumbles into small, relatively blunt pieces, leaving the opening empty. Laminated glass is sheets bonded to an interlayer, so when it breaks the pieces stay stuck in place. Both can be safety glass. Laminated is preferred where falling glass or an open hole would be a hazard.
How much does toughened glass cut to size cost?
The price depends on the dimensions, thickness, glass type, edge finish, number of holes and cut-outs, any shapes, and whether you want supply only or fitting. Laminated, low-iron and obscure glass cost more than clear toughened. See the guide prices for typical panels, then get a written quote for your exact specification.
Can toughened glass be cut or drilled after it is made?
No. Toughened glass cannot be cut, drilled or edge-worked once it has been toughened, because any damage to the surface releases the internal stress and the whole pane shatters. All sizes, holes and cut-outs must be finalised before toughening. That is why accurate measurements or a template are needed before the order is placed.
Why do I need to wait for toughened glass?
Toughened glass is made to order. Each panel is cut, edge-worked and drilled from float glass, then heated and cooled in a toughening furnace. It cannot be cut from stock once toughened. Your written quote shows the expected timescale, and the glazier will confirm fitting arrangements once the glass is ready.
Do you cover Andover for safety glass?
Yes. We can quote for safety glass across Andover and the surrounding Hampshire area, including postcode districts SP10, and nearby Winchester, Newbury and Salisbury. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Andover
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.