Folkestone · Kent
Safety Glass in Folkestone
Our glaziers cover Folkestone for laminated glass that stays in place when broken, useful for overhead panels, ground-floor security and family homes.
- CT19
- CT20
- Guide from £55
About toughened glass cut to size in Folkestone
BS EN 12600 classifies safety glass by a pendulum impact test, with class 1 the highest and class 3 the lowest. In England, critical locations generally need at least class 3, and door or side panels wider than 900mm need class 2 or better.
Toughened glass is ordinary float glass that has been cut to size, heated and then cooled quickly with jets of air. This leaves the surfaces in compression, making it several times stronger than untreated glass of the same thickness. When it does break, it crumbles into small, relatively blunt pieces.
In England, Approved Document K requires safety glass in critical locations: glass in a door or within 300mm of a door edge, up to 1500mm above the floor, and other glass within 800mm of the floor. The rules are similar elsewhere in the UK, but the detail differs.
Safety glass in a building should carry a permanent mark, usually in a corner, that stays visible after fitting. It names the maker or supplier and the standard, such as BS EN 12150 for toughened glass. The mark is how a buyer or inspector can confirm what was fitted.
What you get
- Written quote fixing the price for the specification
- Permanent safety marking on building glass
- Measurement or templating of the glass panel
- Advice on toughened or laminated glass for the location
Local details for Folkestone
- Postcodes covered
- CT19, CT20 and the surrounding area, including Dover, Ashford (Kent) and Deal
- Coast
- Folkestone is about 1 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Near the coast, salt spray can mark exposed glass edges and corrode metal fixings. Polished edges and sealed laminated edges cope better outdoors, and stainless steel clamps and hinges are worth specifying for external safety glass panels and screens.
- Daylight and sun
- In Folkestone the midwinter sun reaches about 16° above the horizon at noon, with roughly 7.7 hours of daylight, rising to about 62° and 16.3 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- In flats and city buildings, large panels of safety glass may need to fit through narrow stairs, lifts and doorways. Measuring access routes at the survey avoids problems, and laminated glass suits ground-floor doors and screens facing the street.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Folkestone
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
What you can choose
Clear toughened glass
Heat-treated float glass that breaks into small, blunt pieces, for doors, screens, tabletops and shelves in a range of thicknesses.
Holes and cut-outs
Drilled holes for handles, hinges and fixings, and cut-outs for sockets, all made before the glass is toughened.
Toughened laminated glass
Toughened sheets laminated together, combining strength with post-breakage retention, often used for frameless panels and higher-load applications.
Safety Glass in Folkestone: questions
Should I choose a polished or arrised edge?
Choose polished edges where the edge will be seen or touched, such as tabletops, shelves and frameless panels, because they are smooth and look neat. Arrised edges are lightly sanded to remove sharpness and are fine where the edge sits hidden in a frame. Bevelled edges are decorative and suit mirrors and some tabletops.
Can toughened glass be cut or drilled after it is made?
No. Toughened glass cannot be cut, drilled or edge-worked once it has been toughened, because any damage to the surface releases the internal stress and the whole pane shatters. All sizes, holes and cut-outs must be finalised before toughening. That is why accurate measurements or a template are needed before the order is placed.
What thickness of toughened glass do I need for a table or shelf?
It depends on the size, how the glass is supported and the load it will carry. Small side tables can use thinner glass, while large dining tables and long shelves need thicker panels to limit bending. Tell us the dimensions, support method and what it will hold, and we will confirm a suitable thickness in the quote.
Where is safety glass required in a house?
In England, safety glass is needed in critical locations: glass in doors and within 300mm of a door edge, up to 1500mm above floor level, and other glass within 800mm of the floor. Small panes and leaded lights have specific exceptions. The rules elsewhere in the UK are similar, but the detail differs between nations.
Do you cover Folkestone for safety glass?
Yes. We can quote for safety glass across Folkestone and the surrounding Kent area, including postcode districts CT19 and CT20, and nearby Dover, Ashford (Kent) and Deal. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Folkestone
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.