Norfolk · England
Glass Splashbacks in Norfolk
From a single panel behind a hob to a full kitchen wall, we can quote for glass splashbacks in Norfolk with joints planned neatly at corners and natural breaks.
- Guide from £225
- 7 towns covered
- Postcode areas IP, NR, PE
Glass splashback behind hob in Norfolk
Colours look different on screens, in daylight and under kitchen lighting, so choose from a physical glass sample rather than a website or paint chart. We can match many paint and RAL colours, and a sample panel viewed in your own kitchen avoids surprises.
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
The price depends on the total glass area, the number of panels and joints, the number of cut-outs, the colour and glass type, and access to the wall. Low-iron glass, metallic or printed finishes and complex shapes add cost. See the guide prices for typical ranges.
Towns we cover for glass splashbacks in Norfolk
Choose your town for local details, nearby areas and the postcode districts we cover.
What applies in Norfolk
Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Norfolk has its own coastline, so for homes and businesses near the sea, salt air and wind-driven rain are part of the brief. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
Guide prices
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Glass Splashbacks in Norfolk: questions
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
Can a glass splashback be fitted over existing tiles?
It is usually better to remove the tiles and make the wall good first. Glass needs a flat, sound surface for the adhesive to bond evenly, and grout lines, uneven tiles or loose tiles can show through or create stress points. Removing tiles also stops the glass standing too far forward of the worktop and sockets.
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
Which parts of Norfolk do you cover for glass splashbacks?
We cover the whole of Norfolk, including Norwich, Great Yarmouth, King's Lynn, Thetford and Dereham, and postcode areas IP, NR, PE. Building rules for glass splashbacks here follow the regulations for England. Enter your postcode on the quote form and we will confirm cover; then a glazier will arrange a free survey before giving you a written quote.
Other glazing services in Norfolk
- Replacement Glass in Norfolk
- Misted Glass Repair in Norfolk
- Emergency Glazing in Norfolk
- Safety Glass in Norfolk
- Window Repairs in Norfolk
- Window Film in Norfolk
- uPVC Windows in Norfolk
- Aluminium Windows in Norfolk
- Sash Windows in Norfolk
- Composite Doors in Norfolk
- Bifold Doors in Norfolk
- Sliding Doors in Norfolk
- Secondary Glazing in Norfolk
- Roof Lanterns in Norfolk
- Glass Balustrades in Norfolk
- Frameless Glass in Norfolk
- Shower Screens in Norfolk
- Bespoke Mirrors in Norfolk
- Glass Roofs in Norfolk
- Shopfront Glazing in Norfolk
- Curtain Walling in Norfolk
- Glass Partitions in Norfolk
- Property Glazing in Norfolk
Get a written quote in Norfolk
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.