Northallerton · North Yorkshire
Glass Splashbacks in Northallerton
Fitting a new kitchen in Northallerton? Once the worktops and hob are in, we can template, colour-match and fit glass splashbacks that line up with your units and sockets.
- DL7
- DL6
- Guide from £225
Glass splashbacks in Northallerton: what to know
Glass splashbacks have no grout lines to stain, so cleaning is simply a soft cloth with warm soapy water or a non-abrasive glass cleaner. Avoid scourers, abrasive creams and sharp scrapers, which can scratch the glass surface and dull the finish over time.
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
Included as standard
- Survey and templating after worktops and hob are fitted
- Back-painting to your chosen colour or finish
- Toughened glass made to template with factory cut-outs
- Bonding with adhesive compatible with the painted back
About Northallerton for this job
- Postcodes covered
- DL7, DL6 and the surrounding area, including Darlington, Ripon and Thornaby-on-Tees
- Coast
- Northallerton is well inland, around 35 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Northallerton the midwinter sun reaches about 12° above the horizon at noon, with roughly 7.0 hours of daylight, rising to about 59° and 17.0 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Northallerton
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
What you can choose
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Glass Splashbacks in Northallerton: questions
How do I clean a glass splashback?
Wipe it with a soft cloth and warm soapy water, or a non-abrasive glass cleaner, then buff dry for a streak-free finish. Grease behind the hob comes off easily because there are no grout lines. Avoid scourers, abrasive creams and blades, which can scratch the glass, and do not use cleaners that could seep behind the edges.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
What affects the cost of a glass splashback?
The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.
Do you cover Northallerton for glass splashbacks?
Yes. We can quote for glass splashbacks across Northallerton and the surrounding North Yorkshire area, including postcode districts DL7 and DL6, and nearby Darlington, Ripon and Thornaby-on-Tees. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Northallerton
Get a written quote in Northallerton
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.