Oxfordshire · England
Glass Splashbacks in Oxfordshire
Want a wipe-clean wall behind a basin or vanity in Oxfordshire? We can quote for toughened glass splashbacks in colours, satin finishes or clear glass over a feature wall.
- Guide from £225
- 10 towns covered
- Postcode areas OX, RG, SN
Toughened glass splashback in Oxfordshire: what to know
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
What applies in Oxfordshire
Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Oxfordshire is inland, around 56 km from the nearest coast at its closest point, so salt exposure is rarely a factor.
Kitchens in flats and terraces often have narrow access and tight stairs, so long splashbacks may be split into shorter panels with planned joints. Parking for the fitting team and building rules on working hours can also affect scheduling.
Guide prices
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Metallic or sparkle finish
Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.
Glass Splashbacks in Oxfordshire: questions
How do you match the colour of a glass splashback?
We can match many paint and RAL colours, and the most reliable way to choose is from a physical glass sample viewed in your own kitchen. Colours look different on screens and under different lighting. For pale colours we usually suggest low-iron glass, because standard glass adds a green tint to the painted back.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Which parts of Oxfordshire do you cover for glass splashbacks?
We cover the whole of Oxfordshire, including Oxford, Banbury, Abingdon, Bicester and Didcot, and postcode areas OX, RG, SN. Building rules for glass splashbacks here follow the regulations for England. Enter your postcode on the quote form and we will confirm cover; then a glazier will arrange a free survey before giving you a written quote.
Other glazing services in Oxfordshire
- Replacement Glass in Oxfordshire
- Misted Glass Repair in Oxfordshire
- Emergency Glazing in Oxfordshire
- Safety Glass in Oxfordshire
- Window Repairs in Oxfordshire
- Window Film in Oxfordshire
- uPVC Windows in Oxfordshire
- Aluminium Windows in Oxfordshire
- Sash Windows in Oxfordshire
- Composite Doors in Oxfordshire
- Bifold Doors in Oxfordshire
- Sliding Doors in Oxfordshire
- Secondary Glazing in Oxfordshire
- Roof Lanterns in Oxfordshire
- Glass Balustrades in Oxfordshire
- Frameless Glass in Oxfordshire
- Shower Screens in Oxfordshire
- Bespoke Mirrors in Oxfordshire
- Glass Roofs in Oxfordshire
- Shopfront Glazing in Oxfordshire
- Curtain Walling in Oxfordshire
- Glass Partitions in Oxfordshire
- Property Glazing in Oxfordshire
All glazing in Oxfordshire · Glass Splashbacks across the UK
Get a written quote in Oxfordshire
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.