Bordon · Hampshire
Safety Glass in Bordon
Safety glass for doors, side panels and low windows in Bordon can be made to the right class, with a permanent mark showing the standard.
- GU35
- Guide from £55
Toughened glass panels across Bordon
Safety glass in a building should carry a permanent mark, usually in a corner, that stays visible after fitting. It names the maker or supplier and the standard, such as BS EN 12150 for toughened glass. The mark is how a buyer or inspector can confirm what was fitted.
Edge finish affects both look and safety. Arrised edges are lightly sanded to take off sharpness and suit glass held in frames. Polished edges are smooth and clear for exposed edges on tables, shelves and frameless panels. Bevelled edges add a decorative angled border.
Once glass has been toughened, it cannot be cut, drilled, notched or edge-worked. All shaping, holes for handles or hinges, and cut-outs for sockets must be finished on the float glass first. This is why accurate measuring and templates matter before any order is placed.
In England, Approved Document K requires safety glass in critical locations: glass in a door or within 300mm of a door edge, up to 1500mm above the floor, and other glass within 800mm of the floor. The rules are similar elsewhere in the UK, but the detail differs.
What you get
- Measurement or templating of the glass panel
- Permanent safety marking on building glass
- Glass cut, edge-worked and drilled before toughening
- Advice on toughened or laminated glass for the location
Local details for Bordon
- Postcodes covered
- GU35 and the surrounding area, including Farnham, Aldershot and Fleet
- Coast
- Bordon is well inland, around 30 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Bordon the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.7 hours of daylight, rising to about 62° and 16.3 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- Older rural homes often have internal doors and screens with old, unmarked glass. Upgrading them to toughened or laminated safety glass is common, and timber door frames may need careful beading when the new glass is fitted.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Bordon
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Specification choices
Clear toughened glass
Heat-treated float glass that breaks into small, blunt pieces, for doors, screens, tabletops and shelves in a range of thicknesses.
Heat soak testing
An extra heat test after toughening that reduces the risk of spontaneous breakage from nickel sulphide inclusions in the glass.
Holes and cut-outs
Drilled holes for handles, hinges and fixings, and cut-outs for sockets, all made before the glass is toughened.
Safety Glass in Bordon: questions
Why do I need to wait for toughened glass?
Toughened glass is made to order. Each panel is cut, edge-worked and drilled from float glass, then heated and cooled in a toughening furnace. It cannot be cut from stock once toughened. Your written quote shows the expected timescale, and the glazier will confirm fitting arrangements once the glass is ready.
Can toughened glass be cut or drilled after it is made?
No. Toughened glass cannot be cut, drilled or edge-worked once it has been toughened, because any damage to the surface releases the internal stress and the whole pane shatters. All sizes, holes and cut-outs must be finalised before toughening. That is why accurate measurements or a template are needed before the order is placed.
How much does toughened glass cut to size cost?
The price depends on the dimensions, thickness, glass type, edge finish, number of holes and cut-outs, any shapes, and whether you want supply only or fitting. Laminated, low-iron and obscure glass cost more than clear toughened. See the guide prices for typical panels, then get a written quote for your exact specification.
How do I know if my glass is safety glass?
Look for a permanent mark etched or printed in a corner of the pane. It should name the maker or supplier and the standard, such as BS EN 12150 for toughened glass, or show a BS EN 12600 class. Older glass may have no mark. If you are unsure, a glazier can check and advise.
Do you cover Bordon for safety glass?
Yes. We can quote for safety glass across Bordon and the surrounding Hampshire area, including postcode districts GU35, and nearby Farnham, Aldershot and Fleet. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Bordon
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.