Totton · Hampshire
Safety Glass in Totton
Need a glass panel made to measure in Totton? Our glaziers confirm the thickness, edge finish and holes before the glass is toughened.
- SO40
- Guide from £55
Laminated safety glass in Totton
Laminated glass is two or more sheets bonded with a plastic interlayer, often PVB. If it breaks, the pieces stick to the interlayer and the pane stays in place. That makes it useful for overhead glass, ground-floor security and openings where an empty hole would be a risk.
Safety glass in a building should carry a permanent mark, usually in a corner, that stays visible after fitting. It names the maker or supplier and the standard, such as BS EN 12150 for toughened glass. The mark is how a buyer or inspector can confirm what was fitted.
BS EN 12600 classifies safety glass by a pendulum impact test, with class 1 the highest and class 3 the lowest. In England, critical locations generally need at least class 3, and door or side panels wider than 900mm need class 2 or better.
Toughened glass can, in rare cases, break without any obvious impact because of tiny nickel sulphide inclusions in the glass. Heat soak testing exposes the toughened glass to heat for a set period to break susceptible panes before supply, which reduces the risk without removing it completely.
What you get
- Written quote fixing the price for the specification
- Glass cut, edge-worked and drilled before toughening
- Measurement or templating of the glass panel
- Delivery or fitting by our glaziers
About Totton for this job
- Postcodes covered
- SO40 and the surrounding area, including Southampton, Hythe and Eastleigh
- Coast
- Totton is about 5 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Near the coast, salt spray can mark exposed glass edges and corrode metal fixings. Polished edges and sealed laminated edges cope better outdoors, and stainless steel clamps and hinges are worth specifying for external safety glass panels and screens.
- Daylight and sun
- In Totton the midwinter sun reaches about 16° above the horizon at noon, with roughly 7.7 hours of daylight, rising to about 62° and 16.3 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- Older rural homes often have internal doors and screens with old, unmarked glass. Upgrading them to toughened or laminated safety glass is common, and timber door frames may need careful beading when the new glass is fitted.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Totton
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Specification choices
Clear toughened glass
Heat-treated float glass that breaks into small, blunt pieces, for doors, screens, tabletops and shelves in a range of thicknesses.
Low-iron glass
Extra-clear glass with much less green tint, chosen for tabletops, shelving and panels where colour and edge clarity matter.
Heat soak testing
An extra heat test after toughening that reduces the risk of spontaneous breakage from nickel sulphide inclusions in the glass.
Safety Glass in Totton: questions
What is the difference between toughened and laminated glass?
Toughened glass is heat treated so it is stronger and, if broken, crumbles into small, relatively blunt pieces, leaving the opening empty. Laminated glass is sheets bonded to an interlayer, so when it breaks the pieces stay stuck in place. Both can be safety glass. Laminated is preferred where falling glass or an open hole would be a hazard.
How do I know if my glass is safety glass?
Look for a permanent mark etched or printed in a corner of the pane. It should name the maker or supplier and the standard, such as BS EN 12150 for toughened glass, or show a BS EN 12600 class. Older glass may have no mark. If you are unsure, a glazier can check and advise.
Can toughened glass be cut or drilled after it is made?
No. Toughened glass cannot be cut, drilled or edge-worked once it has been toughened, because any damage to the surface releases the internal stress and the whole pane shatters. All sizes, holes and cut-outs must be finalised before toughening. That is why accurate measurements or a template are needed before the order is placed.
Where is safety glass required in a house?
In England, safety glass is needed in critical locations: glass in doors and within 300mm of a door edge, up to 1500mm above floor level, and other glass within 800mm of the floor. Small panes and leaded lights have specific exceptions. The rules elsewhere in the UK are similar, but the detail differs between nations.
Do you cover Totton for safety glass?
Yes. We can quote for safety glass across Totton and the surrounding Hampshire area, including postcode districts SO40, and nearby Southampton, Hythe and Eastleigh. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Totton
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.