Sevenoaks · Kent
Safety Glass in Sevenoaks
Safety glass for doors, side panels and low windows in Sevenoaks can be made to the right class, with a permanent mark showing the standard.
- TN13
- Guide from £55
Toughened glass table top in Sevenoaks
Laminated glass is two or more sheets bonded with a plastic interlayer, often PVB. If it breaks, the pieces stick to the interlayer and the pane stays in place. That makes it useful for overhead glass, ground-floor security and openings where an empty hole would be a risk.
Edge finish affects both look and safety. Arrised edges are lightly sanded to take off sharpness and suit glass held in frames. Polished edges are smooth and clear for exposed edges on tables, shelves and frameless panels. Bevelled edges add a decorative angled border.
Safety glass in a building should carry a permanent mark, usually in a corner, that stays visible after fitting. It names the maker or supplier and the standard, such as BS EN 12150 for toughened glass. The mark is how a buyer or inspector can confirm what was fitted.
The price of safety glass depends on its size, thickness, whether it is toughened or laminated, the edge finish, the number of holes and cut-outs, any shapes or curves, and whether it is supplied only or fitted. Low-iron or tinted glass costs more than clear float.
What a typical job includes
- Permanent safety marking on building glass
- Measurement or templating of the glass panel
- Delivery or fitting by our glaziers
- Advice on toughened or laminated glass for the location
Local details for Sevenoaks
- Postcodes covered
- TN13 and the surrounding area, including Tonbridge, Orpington and Swanley
- Coast
- Sevenoaks is well inland, around 23 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Sevenoaks the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- Older rural homes often have internal doors and screens with old, unmarked glass. Upgrading them to toughened or laminated safety glass is common, and timber door frames may need careful beading when the new glass is fitted.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Sevenoaks
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Choosing your safety glass
Polished edges
Smooth, clear edges for exposed glass on tables, shelves and frameless panels, safer to handle and neater to look at.
Satin or obscure finish
Acid-etched or patterned glass for privacy in doors and screens, toughened or laminated to meet safety requirements.
Holes and cut-outs
Drilled holes for handles, hinges and fixings, and cut-outs for sockets, all made before the glass is toughened.
Safety Glass in Sevenoaks: questions
Should I choose a polished or arrised edge?
Choose polished edges where the edge will be seen or touched, such as tabletops, shelves and frameless panels, because they are smooth and look neat. Arrised edges are lightly sanded to remove sharpness and are fine where the edge sits hidden in a frame. Bevelled edges are decorative and suit mirrors and some tabletops.
What thickness of toughened glass do I need for a table or shelf?
It depends on the size, how the glass is supported and the load it will carry. Small side tables can use thinner glass, while large dining tables and long shelves need thicker panels to limit bending. Tell us the dimensions, support method and what it will hold, and we will confirm a suitable thickness in the quote.
Can toughened glass be cut or drilled after it is made?
No. Toughened glass cannot be cut, drilled or edge-worked once it has been toughened, because any damage to the surface releases the internal stress and the whole pane shatters. All sizes, holes and cut-outs must be finalised before toughening. That is why accurate measurements or a template are needed before the order is placed.
How much does toughened glass cut to size cost?
The price depends on the dimensions, thickness, glass type, edge finish, number of holes and cut-outs, any shapes, and whether you want supply only or fitting. Laminated, low-iron and obscure glass cost more than clear toughened. See the guide prices for typical panels, then get a written quote for your exact specification.
Do you cover Sevenoaks for safety glass?
Yes. We can quote for safety glass across Sevenoaks and the surrounding Kent area, including postcode districts TN13, and nearby Tonbridge, Orpington and Swanley. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Sevenoaks
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.