Fulham · Greater London
Safety Glass in Fulham
Glass tabletops, shelves and splash panels for homes in Fulham can be cut, polished and toughened to your exact size and shape.
- SW6
- SW10
- SW5
- Guide from £55
Toughened glass cut to size across Fulham
Toughened glass can, in rare cases, break without any obvious impact because of tiny nickel sulphide inclusions in the glass. Heat soak testing exposes the toughened glass to heat for a set period to break susceptible panes before supply, which reduces the risk without removing it completely.
Once glass has been toughened, it cannot be cut, drilled, notched or edge-worked. All shaping, holes for handles or hinges, and cut-outs for sockets must be finished on the float glass first. This is why accurate measuring and templates matter before any order is placed.
Safety glass in a building should carry a permanent mark, usually in a corner, that stays visible after fitting. It names the maker or supplier and the standard, such as BS EN 12150 for toughened glass. The mark is how a buyer or inspector can confirm what was fitted.
When measuring for a replacement panel, measure the opening or old glass in at least two places for width and height, and note the thickness. For anything with holes, curves or angled corners, a hardboard or card template gives the most reliable result.
What you get
- Advice on toughened or laminated glass for the location
- Glass cut, edge-worked and drilled before toughening
- Written quote fixing the price for the specification
- Permanent safety marking on building glass
Fulham at a glance
- Postcodes covered
- SW6, SW10, SW5 and the surrounding area, including Hammersmith, Chelsea and Kensington
- Coast
- Fulham is well inland, around 39 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Fulham the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- In flats and city buildings, large panels of safety glass may need to fit through narrow stairs, lifts and doorways. Measuring access routes at the survey avoids problems, and laminated glass suits ground-floor doors and screens facing the street.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Fulham
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Options to choose between
Heat soak testing
An extra heat test after toughening that reduces the risk of spontaneous breakage from nickel sulphide inclusions in the glass.
Polished edges
Smooth, clear edges for exposed glass on tables, shelves and frameless panels, safer to handle and neater to look at.
Holes and cut-outs
Drilled holes for handles, hinges and fixings, and cut-outs for sockets, all made before the glass is toughened.
Safety Glass in Fulham: questions
Where is safety glass required in a house?
In England, safety glass is needed in critical locations: glass in doors and within 300mm of a door edge, up to 1500mm above floor level, and other glass within 800mm of the floor. Small panes and leaded lights have specific exceptions. The rules elsewhere in the UK are similar, but the detail differs between nations.
Can toughened glass be cut or drilled after it is made?
No. Toughened glass cannot be cut, drilled or edge-worked once it has been toughened, because any damage to the surface releases the internal stress and the whole pane shatters. All sizes, holes and cut-outs must be finalised before toughening. That is why accurate measurements or a template are needed before the order is placed.
How do I know if my glass is safety glass?
Look for a permanent mark etched or printed in a corner of the pane. It should name the maker or supplier and the standard, such as BS EN 12150 for toughened glass, or show a BS EN 12600 class. Older glass may have no mark. If you are unsure, a glazier can check and advise.
What thickness of toughened glass do I need for a table or shelf?
It depends on the size, how the glass is supported and the load it will carry. Small side tables can use thinner glass, while large dining tables and long shelves need thicker panels to limit bending. Tell us the dimensions, support method and what it will hold, and we will confirm a suitable thickness in the quote.
Do you cover Fulham for safety glass?
Yes. We can quote for safety glass across Fulham and the surrounding Greater London area, including postcode districts SW6, SW10 and SW5, and nearby Hammersmith, Chelsea and Kensington. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Fulham
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.