Kensington · Greater London
Safety Glass in Kensington
Safety glass for doors, side panels and low windows in Kensington can be made to the right class, with a permanent mark showing the standard.
- SW3
- SW5
- SW7
- SW10
- W8
- W10
- Guide from £55
Toughened glass panels in Kensington
Safety glass in a building should carry a permanent mark, usually in a corner, that stays visible after fitting. It names the maker or supplier and the standard, such as BS EN 12150 for toughened glass. The mark is how a buyer or inspector can confirm what was fitted.
In England, Approved Document K requires safety glass in critical locations: glass in a door or within 300mm of a door edge, up to 1500mm above the floor, and other glass within 800mm of the floor. The rules are similar elsewhere in the UK, but the detail differs.
Toughened glass is ordinary float glass that has been cut to size, heated and then cooled quickly with jets of air. This leaves the surfaces in compression, making it several times stronger than untreated glass of the same thickness. When it does break, it crumbles into small, relatively blunt pieces.
Edge finish affects both look and safety. Arrised edges are lightly sanded to take off sharpness and suit glass held in frames. Polished edges are smooth and clear for exposed edges on tables, shelves and frameless panels. Bevelled edges add a decorative angled border.
What you get
- Glass cut, edge-worked and drilled before toughening
- Written quote fixing the price for the specification
- Measurement or templating of the glass panel
- Permanent safety marking on building glass
Kensington at a glance
- Postcodes covered
- SW3, SW5, SW7, SW10, W8, W10, W11 and the surrounding area, including Shepherds Bush, Hammersmith and Chelsea
- Coast
- Kensington is well inland, around 39 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Kensington the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- In flats and city buildings, large panels of safety glass may need to fit through narrow stairs, lifts and doorways. Measuring access routes at the survey avoids problems, and laminated glass suits ground-floor doors and screens facing the street.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Kensington
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Choosing your safety glass
Holes and cut-outs
Drilled holes for handles, hinges and fixings, and cut-outs for sockets, all made before the glass is toughened.
Clear toughened glass
Heat-treated float glass that breaks into small, blunt pieces, for doors, screens, tabletops and shelves in a range of thicknesses.
Low-iron glass
Extra-clear glass with much less green tint, chosen for tabletops, shelving and panels where colour and edge clarity matter.
Safety Glass in Kensington: questions
Where is safety glass required in a house?
In England, safety glass is needed in critical locations: glass in doors and within 300mm of a door edge, up to 1500mm above floor level, and other glass within 800mm of the floor. Small panes and leaded lights have specific exceptions. The rules elsewhere in the UK are similar, but the detail differs between nations.
Is laminated glass better for security?
Laminated glass usually gives better security than toughened glass of similar thickness, because the interlayer holds the glass together after it cracks, so making a hole takes more effort. Thicker interlayers and multi-layer laminates give more resistance. For ground-floor windows, shopfronts and doors, laminated glass is often chosen for this reason.
How do I know if my glass is safety glass?
Look for a permanent mark etched or printed in a corner of the pane. It should name the maker or supplier and the standard, such as BS EN 12150 for toughened glass, or show a BS EN 12600 class. Older glass may have no mark. If you are unsure, a glazier can check and advise.
Can toughened glass be cut or drilled after it is made?
No. Toughened glass cannot be cut, drilled or edge-worked once it has been toughened, because any damage to the surface releases the internal stress and the whole pane shatters. All sizes, holes and cut-outs must be finalised before toughening. That is why accurate measurements or a template are needed before the order is placed.
Do you cover Kensington for safety glass?
Yes. We can quote for safety glass across Kensington and the surrounding Greater London area, including postcode districts SW3, SW5, SW7, SW10 and W8, and nearby Shepherds Bush, Hammersmith and Chelsea. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Kensington
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.