Horsham · West Sussex
Safety Glass in Horsham
Our glaziers cover Horsham for laminated glass that stays in place when broken, useful for overhead panels, ground-floor security and family homes.
- RH12
- Guide from £55
Toughened glass table top in Horsham
When measuring for a replacement panel, measure the opening or old glass in at least two places for width and height, and note the thickness. For anything with holes, curves or angled corners, a hardboard or card template gives the most reliable result.
Safety glass in a building should carry a permanent mark, usually in a corner, that stays visible after fitting. It names the maker or supplier and the standard, such as BS EN 12150 for toughened glass. The mark is how a buyer or inspector can confirm what was fitted.
In England, Approved Document K requires safety glass in critical locations: glass in a door or within 300mm of a door edge, up to 1500mm above the floor, and other glass within 800mm of the floor. The rules are similar elsewhere in the UK, but the detail differs.
Toughened glass is ordinary float glass that has been cut to size, heated and then cooled quickly with jets of air. This leaves the surfaces in compression, making it several times stronger than untreated glass of the same thickness. When it does break, it crumbles into small, relatively blunt pieces.
Included as standard
- Permanent safety marking on building glass
- Glass cut, edge-worked and drilled before toughening
- Written quote fixing the price for the specification
- Measurement or templating of the glass panel
About Horsham for this job
- Postcodes covered
- RH12 and the surrounding area, including Crawley, Horley and Haywards Heath
- Coast
- Horsham is well inland, around 26 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Horsham the midwinter sun reaches about 16° above the horizon at noon, with roughly 7.7 hours of daylight, rising to about 62° and 16.3 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- Older rural homes often have internal doors and screens with old, unmarked glass. Upgrading them to toughened or laminated safety glass is common, and timber door frames may need careful beading when the new glass is fitted.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Horsham
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Options to choose between
Toughened laminated glass
Toughened sheets laminated together, combining strength with post-breakage retention, often used for frameless panels and higher-load applications.
Satin or obscure finish
Acid-etched or patterned glass for privacy in doors and screens, toughened or laminated to meet safety requirements.
Low-iron glass
Extra-clear glass with much less green tint, chosen for tabletops, shelving and panels where colour and edge clarity matter.
Safety Glass in Horsham: questions
Can toughened glass break on its own?
Rarely, yes. Tiny nickel sulphide inclusions in the glass can expand over time and cause a toughened pane to break without an obvious impact. Edge damage during fitting can also cause later failure. Heat soak testing reduces the risk of inclusion-related breakage, and careful handling and correct fitting protect the edges.
Why do I need to wait for toughened glass?
Toughened glass is made to order. Each panel is cut, edge-worked and drilled from float glass, then heated and cooled in a toughening furnace. It cannot be cut from stock once toughened. Your written quote shows the expected timescale, and the glazier will confirm fitting arrangements once the glass is ready.
Should I choose a polished or arrised edge?
Choose polished edges where the edge will be seen or touched, such as tabletops, shelves and frameless panels, because they are smooth and look neat. Arrised edges are lightly sanded to remove sharpness and are fine where the edge sits hidden in a frame. Bevelled edges are decorative and suit mirrors and some tabletops.
Where is safety glass required in a house?
In England, safety glass is needed in critical locations: glass in doors and within 300mm of a door edge, up to 1500mm above floor level, and other glass within 800mm of the floor. Small panes and leaded lights have specific exceptions. The rules elsewhere in the UK are similar, but the detail differs between nations.
Do you cover Horsham for safety glass?
Yes. We can quote for safety glass across Horsham and the surrounding West Sussex area, including postcode districts RH12, and nearby Crawley, Horley and Haywards Heath. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Horsham
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.